How to solve the faucet broken in the wall

The faucet is a valve that controls the flow of water. It is our most common hardware accessory. Whether it is a kitchen, a toilet or a laundry in the home, we need a faucet as long as there is water. However, when we replaced the long-time faucet, it was often caused by lack of experience, resulting in improper operation, which eventually caused the faucet to break in the wall. So what do we do when we encounter this kind of difficult problem in life? Let's analyze the reasons why the faucet is broken in the wall and the specific solution.

How to solve the faucet broken in the wall

Why is the faucet broken in the wall? The investigation found that there are two main reasons why the faucet is broken in the wall:

1. It may be that the quality of the parts we purchased is not good, and the installation is too tight during the installation. If it is the decoration of your own home, it is recommended to go to the large building materials to purchase brand products. In addition, when installing, it is just right to do it. The material is only allowed to use raw material tape, and it is not allowed to use hemp.

2, of course, the main reason is that we are not doing enough when disassembling the faucet. When disassembling, it is found that it is very tight and not excessive force. You can drop a little liquid helper at the thread, remove the rust agent, and then remove it after a while.

The maintenance method of the commonly used faucet broken in the wall:

First, go to the hardware store to buy a plan to draw floor tiles, to open the wall. Then the left hand uses a needle-nose pliers to clamp a small cement nail, and the right hand uses a nail hammer to nail the cement nail into the seam, and it will soon be fine. The first chance to succeed is estimated to be only 30% to 40%, and novices should be patient. You can also use a hacksaw blade to pull out a primer and use a flat-blade screwdriver to reverse the tap and rotate it out. You can also find a saw blade to cut the inside of the wall into two opposite gaps. Use a steel sheet of relative width and hardness. Use a flat-blade screwdriver to tighten the screw. Use a pliers to remove the broken wire.

Second, the hardware store has a tool for breaking the thread extractor. If it is not, it can be purchased online. If it is bought, it will be inserted into the wire mouth to break, turn counterclockwise, and the force should be even, then the broken screw can be taken out. The second method is to match the loose rust agent: if it is conditional, re-tapping to make the abrasive tool.

It is worth noting that the faucet should be tested for unloading during repairs. Do not use too much force to unload it back and forth. Loosen and then quickly unload. Always remember: the faucet is turned counterclockwise! Clockwise is off! Whether it is placed backwards or horizontally. If you are not sure, please ask the hydropower master to deal with it, so as not to damage the inner wire and cause more trouble. Finally, it is recommended to buy a good quality faucet to avoid repeating the same mistakes.

I believe that after taking the above suggestions, we can handle it calmly when encountering the problem that the faucet is broken in the wall.

  Medical Casters are used in all sorts of hospital facilities such as sickbeds, medical equipment, high grade restaurants and supermarkets etc. They have advantages like anti-bacteria, static resistance, impact resistance, chemical corrosion resistance, wear resistance, environmental protection and low noise etc. MYWIN could provide different colors and different sizes medical casters including Single Wheel and twin wheels to meet customer's requirement.  

  MYWIN could provide many kinds of medical casters. For example, Medical Trolley Casters, Twin Wheels Medical Casters, Bread Medical Casters, central locking casters, emergency moving bed casters and so on.

 As the quality, our casters have the certification proof and have received testing after production. The regular salt and spray test and load capacity test are taken in our every caster. We also have the SGS, IAF, TUV and CNAS certification to make our customers more confident about our products.

Medical Casters

Medical Casters, Medical Trolley Casters, Twin Wheels Medical Casters, Bread Medical Casters

Ningbo Mywin Caster Co., Ltd. , https://www.mywin-caster.com