Adjustable wrench specifications and precautions

Adjustable wrenches are generally called wrenches in life. They are tools used to tighten or loosen nuts. The opening width of adjustable wrenches can be adjusted within a certain range. Wrenches are very common in life, and they are inseparable when repairing and maintaining some equipment. It is a hardware tool that is very commonly used in maintenance and repair. It is indeed very convenient to use. It also has different specifications and models. the use of. Next, let's take a look at the specifications and models of adjustable wrenches!

 

Adjustable wrench specifications

 

Conventional adjustable wrench specifications and models are generally: "4", "6", "8", "10", "12", "15", "18", "24" models; adjustable wrenches generally use CR -V steel, CR-V steel is an alloy tool steel with chromium-vanadium alloy elements, hardness after heat treatment is 60HRC (Rockwell hardness) or more, carbon steel, chrome vanadium steel and other materials. The largest opening of each adjustable wrench is 1.3, 1.93, 2.4, 3, 3.6, 4.6, 5.5, 6.2 cm.

Open-end wrenches and plum wrenches are generally marked according to the distance (mm) between the two parallel sides of the hexagon nut. The conventional specifications are mainly:

Open-end wrench: 7, 8, 10, 14, 17, 19, 22, 24, 27, 30, 32, 36, 41, 46, 55, 65;

Torx wrench: 6-8, 10-12, 14-16, 18-20, 22-24, 26-28, 30-32, 32-34;

Household general open-end wrenches are: 8-10, 17-19 (for electrical appliances, bicycle maintenance), 30-32 for pipeline maintenance;

Adjustable wrench (GB4440-84)-specifications (length × maximum opening width): 100 × 13 ～ 600 × 65;

Double-ended wrench (double-ended open wrench) (GB4388-84)-specification (opening width): 2.5 ～ 80;

Plum wrench (GB4388-84)-specification (width across edge): 5.5 ～ 36;

Socket wrench (with rotation) (GB3390.2-82)-specification (width on opposite side): 6.3 ～ 63 .

 

Notes on the use of adjustable wrench

 

There are many types and specifications of wrenches, although there are open wrenches, plum wrenches, adjustable wrenches, socket wrenches, torque wrenches and so on. But the method of use and precautions are similar.

1. No matter what kind of wrench. The best use effect is pulling, if it has to be pushed. It can only be pushed with the palm of your hand, and your fingers should be spread out to prevent the bolts or nuts from suddenly loosening and hurting your fingers. To get the maximum torque. The direction of the pulling force must be at right angles to the wrench handle.

2. When using adjustable wrenches. The specifications should be selected according to the size of the nut. When in use, hold the handle with your right hand. The closer the hand is to the back, the more effort it takes to pull it up. When pulling the large nut, a large torque is required, and the hand should be held near the end of the handle. When pulling the small nut. The torque required is not large, but the nut is too small and easy to slip. Therefore, the hand should be held close to the head. The worm gear can be adjusted at any time to tighten the active lips and prevent slippage.

3. When using an adjustable wrench. The movable jaws of the wrench should bear the thrust and fix the jaws and bear the pulling force, that is, when the wrench is pulled. The movable jaws face inwards: the force must be even to avoid damage to the wrench or the deformation of the corners of the bolts and nuts. An accident caused by skidding.

4. Avoid excessive force when using a wrench. otherwise. It may cause skidding and hurt the human body.

5. The wrench should not be used as a crowbar or hand hammer.

6. When pulling the rusty nut. A few drops of kerosene or motor oil can be placed on the nut. After a period of time. Just twist it. When tightening, do not use steel pipes on the handle of the adjustable wrench to increase the torque. Because it is very easy to damage the active lip or the nut, the nut cannot be removed.

7. When a wrench is required for climbing operations. It must be passed by ropes, not thrown up or down.

The above is the introduction about the specifications of the adjustable wrench. By reading the above content, you should be able to understand the relevant knowledge of the adjustable wrench more clearly. In fact, as long as you have a good grasp of the specifications and models in life, then in When choosing an adjustable wrench, you can choose the wrench of the corresponding specification and model according to the actual needs.

product description	Round rainfall head concealed thermostatic Faucet mixer shower set
Brand Name	HP
Material	Brass main body and Brass&ABS handle
Material Analysis	Cu≥ 59%
The Thickness of chrome plating	Nickel:7.5-9.5um  Chrome:0.25-0.45um
Salt spray test	24h
Water flow	Bath/shower mixer â‰¥ 18L/min
Operating pressure	0.05 Mpa-0.8 Mpa
Recommend pressure	0.1 Mpa-0.5 Mpa
	if>0.5Mpa Installation of a flow reducer is recommended
Cold water temperature	4℃-29℃
Hot water temperature	50℃-80℃
Temperature range	20℃-50℃
Security stop	38℃
Cold water supply failure test	Within 5 seconds after cold water supply fails,  outflow  rate automatically drops to 1.9L/Min,  outflow quantity:≤150ml
Life test	CSA B125-98 ASSE 1016(<=100,000 cycles)
Outflow temperature Auto-adjusting sensitivity	When inlet water temperature or pressure varies,  outlet water temperature change will be less than Â±2℃
Application	For family bathroom, hotel bathroom and so on
Standard Apply	CSA B125-98 ASSE 1016
	EN1111 AS-4032.1,cUPC
Quality Guarantee	5 Years Quality Guarantee

Round Conceal Shower Set

Round Concealed Shower Set,Concealed Shower Mixer Installation,Concealed Round Rainfall Shower,Round Brass Concealed Shower Set

KaiPing HuiPu Shower Metalwork Industrial CO,LTD , https://www.hp-shower.com