Common edging title in stone processing

The so-called edging is the grinding of one side or several sides of a sheet into a stone processing technique with a geometric shape. The common edging title in stone processing: chess pieces, French chess pieces, French side, large round side, 1/4 round side, double side, sea side, concave side (crescent side), beveled side, groove side, The mouth of the chicken, double 1/4 round side, duckbill side, see the light side, oblique side + see the light side.

The various titles are shown in the table below:

1. Wool: A stone that is directly separated from the mine and has irregular shapes.

2. Block material: It is made of wool material and has a hexagonal surface. It is used to process stone materials for facing stone.

3, the material stone: processed with wool material with a certain size, used in the construction of stone.

4. Hairboard: A plate with a certain thickness and a surface without any treatment cut by a circular saw, sand saw or frame saw.

5. Rough sheet: The surface is flat and rough with a relatively regular processing mark.

6. Axe plate: A rough plate made of an axe.

7. Hammering plate: A rough surface plate processed with a flower hammer.

8. Fire-burning plate: A rough-faced veneer made of flame produced by using acetylene, oxygen or propane or petroleum liquefied gas as fuel.

9. Burning and adding water to the plate: a plate that is first fired and then impacted with water.

10. Water-flushing plate: The plate processed with water impact, the surface of the plate impacted by water is distributed with small holes and pits, and the natural color of the stone is basically presented.

11. Planer sheet: A rough sheet material processed by machine planing.

12, fine surface plate: smooth and smooth surface.

13. Mirror plate: The surface is flat and has a glossy surface.

14. Matte sheet: A sheet with a smooth surface and low luminosity.

15. Antique stone: The matte surface plate is made of a series of stone grinding brushes. Some antique stones are first fired, and then polished with a series of abrasive brushes to matt.

16. Thin plate: A plate with a thickness of less than 15 mm.

17. Thick plate: A plate with a thickness greater than 15 mm.

18, ordinary type of plate: square or rectangular plate.

19. Shaped sheet: Non-square or non-rectangular sheet.

20, natural surface plate: the surface is twisted with a tweezers or a hammer to form a sheet of a mountain watch.

21. Litchi noodle plate: A plate that is struck on the surface with a hammer shaped like a lychee.

22, longan sheet: use a hammer to cross-stitch the surface of the stone to form a sheet such as longan.

23, blind stone: the surface is concave and convex, the plate is installed on the blind road.

24, machine cutting plate: the surface of the machine to cut out the traces of the sheet.

25. Mushroom surface plate: The surface is hammered with a chisel and a hammer to form a sheet of undulating mountain shape.

26. Pineapple noodle plate: A plate with a surface appearance such as pineapple skin.

27. Edging board: A plate that is ground into a geometric shape on one side of the board.

28. Countertop: The board used as a countertop in the decoration.

29, stair treads: used as a stepping board in the decoration.

30. Sandblasting board: Using corundum as an auxiliary material, the surface of the stone is sprayed into a matte surface under a certain pressure.

31. Engraving board: The surface of the stone is engraved with a variety of patterns.

32. Slotting: Open pits of a certain depth and width on the board.

33. Chicken mouth: Open a 5*5mm L-shaped notch on the edge of the board.

34. Bottom: The process of cutting a certain angle on the bottom surface of the thickness in the direction of the length (or width) of the sheet.

35. Kneading: The process of cutting a certain angle on the upper surface of the thickness direction of the long (or wide) side of the sheet.

36. Small rounded edge: R is less than 10 mm of 1/4 rounded edge.

37, large round side: R is greater than 10mm 1/4 round side.

38, small oblique side: oblique length less than 14mm oblique.

39. Large oblique side: oblique side with an oblique length greater than 14 mm.

40. Seaside skirt: It is composed of two vertical sides and a round edge of less than 1/4 in the middle.

41. See the edge of the light: the two adjacent sides are polished at 80 degrees or more.

42. French side: It is composed of a small straight side and a 1/4 round side.

43, chess pieces: semi-circular sides.

44. French chess piece side: It is composed of a small straight side and a 1/2 round side.

45. Two-level French side: It is composed of two small straight sides and a 1/2 round side in the middle. Or a combination of two French sides.

46. ​​Two-level chess pieces: Two semi-circular sides are connected by two 1/4 round edges.

47. Duckbill: It is shaped like a duckbill.

48. Light body column: column without other processing on the surface of the column.

49. Conical column: The prime line on the surface of the column is extended to the intersecting column.

50. Cylinder: The plain lines on the surface of the column are parallel columns.

51. Elliptical column: a column having an elliptical cross section.

52. Spindle column: A column having a cross-sectional shape such as a spindle.

53. Roman column: The column on the surface of the column has a Roman trough.

54. Plum blossom column: The cross-sectional shape is a plum-shaped column.

55. New column: A column with a cross-sectional shape of a thread.

56. Multi-color column: A column made of a variety of stone bonding.

57. Stigma (column top): The part installed at the top of the column.

58. Column waist: The part that is installed at the waist position of the column body.

59. Column seat: The part installed at the bottom of the column.

60. Handle: A small cylinder that is mounted on the door and acts as a sliding door.

61. A square column and a column having a rectangular cross section.

62. Arc plate: A curved plate with a certain radius and arc length, which can be composed of a cylinder, an elliptical column or other cylinders.

63. Straight line: A flower line whose extended trajectory is a straight line.

64. Curved line: The extended track is the curve of the curve.

65. Plane straight flower line: the decorative surface is a flat straight flower line.

66. Step straight flower line: The straight line of the decorative surface is the step.

67. Arc straight flower line: The straight line with the cross-sectional shape of the arc.

68. Composite straight flower line: The cross-sectional shape is a straight flower line composed of a plurality of arcs or steps.

69. Ceiling line: The flower line installed at the position of the Qitian shed.

70, waist line: installed on the wall roughly waist

Flower line.

71. Foot line: The flower line installed at the ground.

72. Corner line: A line used for wall corners or pillar buckles.

73. Door line: A line that forms a door arch at the door.

74. Handrail line: used as a line for handrails.

75, railing line: used as a railing line.

76. Eaves line: the lines installed at the eaves.

77. Window cover: A line that forms a window arch at the window.

As the name suggests, flame cutting machines are cut by oxyacetylene or oxyfuel. 
1. CNC Flame Cutting Machine is the earliest and best CNC cutting equipment. Flame Cutting Machine is mainly used in heavy industries with low precision requirements, such as sheet metal, steel structure, shipbuilding, machinery and construction. 
2. The flame cutting machine is suitable for the cutting of carbon steel plates of 5mm or more.
3. Economical and practical.

Flame Cutting Machine

Flame Cutting Machine,Cnc Machine,Cnc Plasma Table,Air Plasma Cutting Machine

Jinan Huaxia Machinery Equipment CO.,Ltd , https://www.cnmetalcutting.com