![<?echo $_SERVER['SERVER_NAME'];?>](/template/twentyseventeen/skin/images/header.jpg)
>>>Related Links: Identification methods for superior and inferior large core boards
1. If the length and height of the cabinet exceeds 2,4 m, the horizontal plate of the vertical plate is overlapped with the two plates of the nine plates to ensure the consistency with the thickness of the large core plate. For those who use a large core board to overlap, the penalty worker is 30 yuan per time, and the ordinary nine-percent board overlaps. The penalty worker is 30 yuan per time.
2, the open structure board with a plane to flatten the edge, and use sandpaper to get rid of the burr, in accordance with the structure of the drawings to do with the code nails will be five plywood nailed back. The open material was not planed with a plane, the burr was not scratched with sandpaper, and the pencil and latex of the cabinet were not removed. The foreman was fined 30 yuan; the pliers were used to nail the nails, or the back plate was made of 9 PCT plates. (except in exceptional circumstances), the foreman shall fine a fee of 30 yuan, and the team leader shall use waste materials.
3. When the cabinet lines are shut and the side finishes, attention should be paid to the height of the veneer on both sides of the cabinet and the height of several facing lines to keep the height of the mouth in order to avoid height differences from the sides of the cabinet. Where the height difference exceeds 1mm, the carpenter team leader reworks the foreman and he is fined 30 yuan.
4, the door frame with a high quality nine PCT board open 60mm, double-sided dislocation slot, the distance between the slots is 150mm. The horizontal clearance distance of the Jiuli board is 200mm, and its interface gap is not more than 1mm. Where the above conditions are not met, the woodworking team leader shall pay compensation materials and the foreman shall be fined 30 yuan.
5, the door of the material: the nine PCT slats on both sides evenly coated with opal white plastic, 1 door double-sided mixed paint, double-sided double-clip PCT board, without lines shut. Where the outer layer did not use the entire three PCT board or close it with a line, the carpenter team leader reworked and the foreman was fined 30 yuan. 2 The oil varnish on the outside of the door, the outside embossed panel and the three PCT board, the inside pressure two layers of three PCT board, the outside brush varnish, brush inside paint. Closed with a line, all non-specified fines are 30 yuan long. 3 The door is the middle of the glass, and paint is mixed inside and outside. The inner and outer sides are hollowed out with the entire plywood. If he did not use the entire three-pronged hollowing out, or if the cabinet door is narrowed, and plywood or lines are used to make up the compensation, the woodworking team leader shall reimburse the compensation materials, and the foreman shall fine a fine of 30 yuan. 4 The glass is embedded in the middle of the door, and the outer side is varnished. Then, the outer panel and the three-ply plate are used, and the inner surface is pressed with two-layer plywood (except for special design requirements).
6. Pressing and placing of cabinet doors: The cabinet doors should be placed on a prefabricated platform, and the external pressure should be more than 100kg and the force should be even (you can consider using a simple fixture), and then press and turn them over 3 days. The pressing time is 7 days or more in summer and 10 days or more in winter. On the lower bar, it indicates the time of pressing and flanging, and the door of the cabinet after pressing is not allowed to be tilted, and it must not be damped to avoid deformation. If there is no time, the penalty for the foreman is 30 yuan. Where there is a phenomenon of degumming after the cabinet doors have been suppressed, the woodworking team leader shall make compensation materials and the foreman shall be fined 30 yuan/time.
7, when the cabinet is used as a partition wall, the back board uses five plywood, the back of the cabinet must be made of 20×40 wooden square made of dragon skeleton with interval of 300×300, and then the paper plasterboard is flatly attached to the keel and fixed. The joints of the backboard shall be misaligned with the joints of the plasterboard, except where otherwise required by the design (silica wool shall be added) to ensure the protection against cracking and sound insulation. No 20×40 keel was used on the back of the cabinet. The captain’s fine was 30 yuan. The woodworking team leader paid compensation materials. The gypsum board was fixed with a nail and the foreman was fined 30 yuan.
8, drawer practice: drawer with 12 PCT board to do the box, 5 PCT board to do the floor, white wood line spell corners to receive four borders, with Daxin board plus decorative panel to do the drawer surface (not see seams in the side, drawer panel (With the shelf joints not more than 1mm), varnish type with a corresponding line closed mouth, mixed oil type without lines shut (using nitro varnishes after the use of atlas leveling, grinding), the width of the drawer is narrower than the structure of 25mm (A For the three-level silent drawer rails, install with Φ4×12 self-tapping screws, each with 12 drawers, such as the lacquer type drawer with no lines to close the drawer surface, the foreman will be fined 30 yuan. For example, if the oil-mixed drawer is closed with lines, the foreman will be fined 30 yuan. For example, the drawer surface is a drawer in the cabinet door. There was no increase of 3cm below, no magnetic touch could be installed, the carpentry team leader reworked, and the materials were compensated. The foreman had a fine of 30 yuan. If the drawer track is not installed with 12 Φ4×12 self-tapping screws, each one is less, the foreman will be fined 30 yuan, and if found a prominent screw in the drawer, the foreman will be fined 30 yuan. Before the acceptance of each drawer, the dust on the drawer track should be removed and a little bit of oil should be added to ensure the push and pull flexibility. If it is found that the foreman did not do a fine of 30 yuan.
9, close the process of timber: furniture edge will be the appropriate width of 5mm thick (full-foot) flat solid wood lines edge, at the intersection of the line, must be a line of direction to close the deal after the formation, and then take the other direction of the line In order to ensure that the line and veneer panel seam tightly, the veneer must be 0,5-1mm higher than its base structure, and then pressed with lines. Where the line is lower than the veneer panel, all must be reworked, the material oil woodworking team leader compensation, the foreman fined 30 yuan. Those who lined up and planed the veneer to be planed at the time of planing the lines must be reworked. The carpenter's team leader reworked and paid for the materials. The foreman had a fine of 30 yuan. ≥ 30mm lines can not be coated with plastic, only two sides brushing; ≥ 50mm, but also in the middle of the back slot.
10, kitchen cabinets and balconies will use water to place cabinets, the ground must be bricked floor to do kicking or lift kitchen cabinets, and cabinet materials must be treated to prevent moisture damp. Anything that is not done must be reworked and the foreman must pay a fine of 30 yuan.
11, hardware accessories: The installation location should be appropriate, cabinet doors more than 1m high to install 3 hinges. The position of the upper and lower hinges to the edge is 120mm (if there is a drawer, the position of the inner retreating hinge). Upper and lower mounting magnetic touch. If the cabinet has an internal drawer, the drawer of the lowest layer shall be raised by 30mm and the side shall be 30mm away from the vertical panel to prevent magnetic touch and hinges blocking the access of the drawer. The handle must be installed in an ergonomic position. Avoid bends and avoid ladders. The location of the hinges was incorrect, the openings were wrong, the woodworking team leader had to pay compensation materials, and the foreman had a fine of 30 yuan. There were drawers in the cabinet, the bottom drawer was not lifted by 30mm, the magnetic bumper could not be installed, the woodworker's compensation materials, and the foreman's fine was 30 yuan.
Related Links:
>>> Kitchen decoration and energy-saving materials to buy tips
>>> Cabinet hardware can not ignore the most important hinged cabinet
>>> Decoration Book: Buy woodworking board must read
Decoration Carpentry knowledge Carpentry Furniture Three trees Lacquerware Decorating design Furniture Glass bricks Drawers Cabinets Doors Cabinets Doors Glass cases Glass cabinets Wall cabinets Glass cabinets Doors Glass furniture Kitchen cabinets Doors Glass Doors Doors Kitchen glass Sliding doors
Sintered Saw Blade Co., Ltd. , http://www.nsdiamondtool.com