CNC machine tool mechanical parts: X-axis fault repair

Source: Bearing network time: 2018-04-06

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

X-axis gap is too big fault repair problem: a matching FANUCOMC; model XH754 CNC machine tool; X-axis gap is too large.
Anatomy and disposal process: X-axis clearance consists of coupling clearance, bearing clearance, screw clearance, mechanical elastic clearance, etc. Remove the X-axis guard; power off and shut down; grasp the screw by hand; turn back and forth; feel the free corner Larger; there is a large gap, adjust the X-axis screw bearing clearance; tighten the nut to tighten it and no improvement; therefore doubt the screw nut has a problem. Loosen the screw nut and the table; view; no gaps found , then open the bearing seat flange; look at the screw bearing; found that the two-corner touch bearing (back to back) inner ring has been tightened together; under normal circumstances there should be a gap; clarify that the bearing gap has no adjustment.
According to the outer diameter of the bearing; a small ring of a thickness of 1 mm is placed at the center of the outer diameter of the pair of bearings; the original gap is subtracted; thus the inner ring of the pair has a gap of about 0.8 mm to adjust the allowance. The back nut is properly tightened; the parameter 0535 is set to 0; the X-axis gap is 0. 02mm measured by the dial gauge; the parameter 0535 is set to 15; the X-axis gap is 0. 01mm; the X-axis gap is eliminated.
X-axis encoder alarm fault repair problem: a matching FANUCOMC; model XH754 CNC machine tool; processing 319 alarm.
Anatomy and disposal process: check the repair manual; prompt the pathogen due to the abnormal communication error of the X-axis pulse encoder; check the diagnosis number 760; find its multi-directional position; the repair manual indicates that the pulse encoder is bad or the reaction cable is bad. The encoder cable plug M185 is normal; therefore, it is a problem that the X-axis serial encoder has a problem. It is recognized; in the electric cabinet, the M184 and M194, M185 and M195 and the corresponding motor three-phase drive line are communicated; the fault alarm is changed to 339. The hair lesion is the Z axis; the X-axis encoder is proved to be defective. After replacement; the disease is removed.
Over-the-counter alarm fault repair phenomenon: a matching FANUCOMC; model XH754 CNC machine tool; over-time alarm "OVERTRAVEL-X" occurs when the X-axis returns to zero.
Anatomy and Disposal Process: Check that the X-axis alarm is far from the stroke limit; the X coordinate of the display appears to exceed the X-axis scale; therefore, it is recognized as a soft limit overtravel alarm. Check parameter 0704 is normal; power off; Press the P button to turn on the NC power supply; if the system finishes the zero return without checking the software limit, you can also change the 0704 to -99999999 and then return to zero; if there is no problem; then change it back to the original value. , you can also press P and CAN to power on to eliminate the alarm.

Recommend to friends comments close window

Bearing related knowledge

Talk about the layout and characteristics of tapered roller bearings: Y-bearings with grub screws
NSK bearing in the machine tool pairing bearing use vertical with seated self-aligning bearing classification sheetfed main roller support bearing skills analysis

This article links to http://
Please indicate China Bearing Network http://

Previous: "IKO needle roller bearing corrosion" should focus on the next section: bearing good or bad comparison

Brominated flame retardants (BFRs) are organobromine compounds that have an inhibitory effect on the ignition of combustible organic materials. Of the commercialized chemical flame retardants, the brominated variety are most widely used. They are very effective in plastics and textile applications, e.g. electronics, clothes and furniture. BFRs are commonly used in electronic products as a means of reducing the flammability of the product.

Types of applications

The electronics industry accounts for the greatest consumption of BFRs. In computers, BFRs are used in four main applications: in printed circuit boards, in components such as connectors, in plastic covers, and in cables. BFRs are also used in a multitude of products, including, but not exclusively, plastic covers of television sets, carpets, pillows, paints, upholstery, and domestic kitchen appliances.

Brominated Flame Retardant Compounds

Decabromodiphenyl oxide(DBDPO)	1163-19-5
Ethane-1,2-bis(pentabromophenyl)(DBDPE)	84852-53-9
Ethylene bis-tetrabromophthalimide	32588-76-4/5
Tetrabromobisphenol A(TBBA)	79-94-7
Hexabromocyclododecane(HBCD)	3194-55-6
Tetradecabromo- diphenoxybenzene	58965-66-5
Brominated Polystyrene	88497-56-7
Brominated Polystyrene	88497-56-7
Tetrabromophthalate Diol(TBPD)	77098-07-8 20566-35-2
Tetrabromophthalic anhydride(TBPA)	632-79-1
Brominated Epoxy	68928-70-1
Poly pentabromobenzyl acrylate	59447-57-3
2,3,4,5,6-Pentabromobenzyl acrylate	59447-55-1
Ammonium Bromide	12124-97-9
2,4,6-Tris(2,4,6-tribromophenoxy)-1,3,5 triazine	25713-60-4
Tris(tribromoneopentyl)phosphate(TTBP)	19186-97-1
Tribromoneopentyl alcohol(TBNPA)	36483-57-5 1522-92-5
Dibromoneopentyl glycol(DBNPG)	3296-90-0
2,4,6-tribromophenol	118-79-6
TetrabromobisphenolA Bis(2,3-dibromopropyl ether)(BDDP)	21850-44-2
Carbonate Oligomer of Tetrabromobisphenol A (BC-52)	94334-64-2
Carbonate Oligomer of Tetrabromobisphenol A (BC-58)	71342-77-3
Tetrabromobisphenol A bis(allyl ether) (BE)	25327-89-3
Tetrabromophthalate Ester(TBPE)	26040-51-7
Bis(Tribromophenoxy)Ethane (BTBPE)	37853-59-1
Polydibromostyrene	148993-99-1
1,3,5-Tris(2,3-dibromoisopropyl) isocyanurate(TBC)	52434-90-9
Tribromophenyl allyl ether (TPE)	3278-89-5

Brominated Flame Retardant

Brominated Flame Retardant Chemicals, Brominated Flame Retardant Materials,Decabromodiphenyl Ethane,Substitution Of HBCD,Tetrabromophthalate Diol, Brominated Polystyrene,Tetrabromobisphenol A

Shandong Novista Chemicals Co.,Ltd (Novista Group) , https://www.novistachem.com